OIS Driver User Guide

Introduction

The OIS driver plugin is used to control the LC898122AXA OIS module. It provides control for quite a few features of the OIS module. These features are explained in this user guide.
This module has been enabled with the AR2520 and the AR1335 sensors so far. If your sensor is not supported, this plugin will not show up in the Plug-ins menu. To add new sensors, please contact the dev team.
To Start the OIS Driver plugin, start DevWare/DevWareX application and load the sensor data file for the sensor. Load the INI preset required, and get the sensor to stream. Then go to Plug-ins->OIS Driver.
The following window comes up.

Figure 1 OIS Driver Plugin Dialog

OIS Driver Features

Initialize OIS Driver Button – Click this to initialize the OIS module.

Calibration Data

The EEPROM is used to store the Calibration data. The user can enter the EEPROM slave address and start address from which to load the EEPROM data. It is assumed that the EEPROM data is stored in the following format. If the format of the calibration data stored in the EEPROM changes, please contact the dev team.

Data Addr	Data	Explanation
0x00	0x4C	Pattern (MSB)
0x01	0x43	Pattern-2
0x02	0x38	Pattern-3
0x03	0x39	Pattern (LSB)
0x04	0xCC	Hall offset X (MSB)
0x05	0x3A	Hall offset X (LSB)
0x06	0xE7	Hall offset Y (MSB)
0x07	0xD6	Hall offset Y (LSB)
0x08	0xF5	Hall bias X (MSB)
0x09	0x00	Hall bias X (LSB)
0x0A	0xE0	Hall bias Y (MSB)
0x0B	0x00	Hall bias Y (LSB)
0x0C	0x07	Hall AD offset X (MSB)
0x0D	0xE7	Hall AD offset X (LSB)
0x0E	0x04	Hall AD offset Y (MSB)
0x0F	0xC0	Hall AD offset Y (LSB)
0x10	0x27	Loop gain X (MSB)
0x11	0xA2	Loop gain X (LSB)
0x12	0x26	Loop gain Y (MSB)
0x13	0x6B	Loop gain Y (LSB)
0x14	0x00	Optical center X (MSB)
0x15	0x00	Optical center X (LSB)
0x16	0x00	Optical center Y (MSB)
0x17	0x00	Optical center Y (LSB)
0x18	0xFF	Gyro offset X (MSB)
0x19	0xFF	Gyro offset X (LSB)
0x1A	0xFF	Gyro offset Y (MSB)
0x1B	0xFF	Gyro offset Y (LSB)
0x1C	0x4C	OSC value
0x1D	0xBF	Gyro gain X [31 : 24]
0x1E	0x14	Gyro gain X [23 : 16]
0x1F	0x7B	Gyro gain X [15 : 8]
0x20	0x00	Gyro gain X [7 : 0]
0x21	0x3F	Gyro gain Y [31 : 24]
0x22	0x14	Gyro gain Y [23 : 16]
0x23	0x7B	Gyro gain Y [15 : 8]
0x24	0x00	Gyro gain Y [7 : 0]

Slave Address – Enter the slave address of the EEPROM.
Start Address – Enter the start address at which the contents are stored. The first 4 bytes must be the pattern mentioned above, if the EEPROM data is valid.
Load Calibration Data Button – Click this button after entering the Slave and Start addresses, to load calibration data from the EEPROM to the OIS module.

OIS Control

There are two modes of OIS control, automatic and manual.
Manual Control
The default is manual control. It exposes two sliders, one for X direction, and other for Y direction. Slide these to see the lens moving in X and Y direction respectively. The hall sensor values can also be accessed by clicking the "Read values" button. The range for this data is -0.4 to + 0.4.
Auto OIS
This enables the OIS module in the LC898122. User can select movie mode or still mode using the radio buttons.

Focus control

This plugin provides manual focus control. There are two types of VCM drive supported with the LC898122 module, i.e. differential and single ended. Select the appropriate value. Please note that this re-initializes the OIS module. You have to reload Calibration data, if you are not using the default values.
After selecting the VCM drive, control the lens position with the slider.

Test Gyro

This plugin also provides a way to test the Gyro. Click this button to run the test. The status will show up below.

Figure 2 Gyro Test Succeeded

OIS Driver User Guide0